How to install oil catch can on 1988 c1500
- HOW TO INSTALL OIL CATCH CAN ON 1988 C1500 DRIVERS
- HOW TO INSTALL OIL CATCH CAN ON 1988 C1500 PRO
- HOW TO INSTALL OIL CATCH CAN ON 1988 C1500 CODE
HOW TO INSTALL OIL CATCH CAN ON 1988 C1500 CODE
Note About Radio Code: On many newer vehicles, whenever the battery is disconnected a radio code is needed to get the stereo working again. Safety Tip: To eliminate any chance of battery arching, after removing the battery cable, wrap a rag around the cable end and place a wrap over the battery terminal. Move the cable end away from the battery post. Park your vehicle on a flat concrete surface, put the shifter in Park, set the emergency brake, pull the hood latch and then open the hood.ġ) Remove the negative battery cable. Note: Depending on your vehicle, additional labeled containers may be needed. > Torque Converter to Flywheel Bolts (or Nuts) > Exhaust and Exhaust Heat Shield Bolts/Nuts > Transmission Oil Cooler Line Fitting Washers > Transmission Oil Fill/Dipstick Tube Bracket Bolt or Nut It’s best to get all the containers or baggies labeled before starting the job.įor removing the transmission from a rear wheel drive vehicle, you will need the following labeled containers/baggies. Organize nuts and bolts: For organizing nuts and bolts, we recommend using labeled plastic containers or baggies, whichever you have available. organized is important for two reasons… 1) it will save you time and frustration when re-installing the transmission and 2) it will insure all nuts and bolts are replaced in their original locations. Check out Gold Eagle‘s car maintenance products to get you started today.Keeping nuts, bolts, washers, clamps, etc. No matter how you take care of your vehicle, you have options to keep it running efficiently. A product like No Leak actually works inside your car to condition the internal seals. A leak could have a number of causes, one of which is a deficiency in the oil seals.
![how to install oil catch can on 1988 c1500 how to install oil catch can on 1988 c1500](https://i.ytimg.com/vi/1VrQuAgYLNA/maxresdefault.jpg)
You can spot oil leaks a number of ways, like your dipstick level dropping, blue smoke from the tailpipe, or a burning oil smell. In addition to blowby, your engine can also leak oil. There are other preventive measures you can take to extend the life of your car.
HOW TO INSTALL OIL CATCH CAN ON 1988 C1500 PRO
This is a big job, but there are commercial products such as the 104+ Fuel Injector Pro to help you do it. One is the removal of the manifold in the DFI engine so the deposits can be cleaned off. However, if you do not install one, you have to take other steps to deal with the effects of blowby in your vehicle. Strictly speaking, any car can continue to run without an oil catch can. This is because, for these cars, optimal performance at all times is essential.Īlso, because of the greater potential for deposit buildup than in older engines, cars with newer gasoline direct injection (GDI) or direct fuel injection (DFI) engines especially benefit from oil catch can technology.
HOW TO INSTALL OIL CATCH CAN ON 1988 C1500 DRIVERS
However, drivers of high-performance vehicles potentially have the most to benefit from the installation of an oil catch can. That would lead to the conclusion that all engines could potentially benefit from an oil catch can. No engine works to optimal efficiency with blowby cycling through, and all engines will suffer irreperable damage over time. What types of vehicles benefit from their use? They also shorten the life of components so you may have to do maintenance more often. Carbon deposits reduce the efficiency of your engine, causing disruptive shaking during idling and unexpected ignition failures. Among those deposits are carbon, which must be removed. The result is a buildup of deposits that reduce engine efficiency. If the blowby cycles through, that air is no longer fresh. Ideally, the engine should use fresh air to start and run. Preventing the blowby from entering the air intake keeps the engine in better condition. Although there are some commercial oil catch cans available, some people create homemade models from old food jars or steel wool. The excess oil collects in the catch can, which must be periodically emptied and rinsed. The oil catch can is placed between the pcv valve and the crankcase. The oil catch can stops that blowby from going back into the air intake of the engine. But very often the process creates the oily blowby.
![how to install oil catch can on 1988 c1500 how to install oil catch can on 1988 c1500](https://i.ebayimg.com/images/g/YDwAAOxyaURTfSB~/s-l300.jpg)
Ideally, the oil that lubricates the pistons - necessary for the engine function - is at a precise measure with no waste. What is an oil catch can?Īn oil catch can captures the excess oil that passes through the piston seals into the crankcase of your car. If you look under the hood of a car and see an oil catch can, it’s an after-purchase addition, designed to increase the engine’s efficiency by reducing blowby that is otherwise sent back into the engine’s intake. It’s hard to imagine that, with all the talk about oil catch cans, that no car comes from the factory with one already installed.